Supra Remove Rear Parking Brakes
2021年11月18日Download here: http://gg.gg/wxcb7
*Supra Rear Wheel Drive
*Toyota Supra Rear Differential
*Supra Rear End
To find your Toyota Supra Rear Brakes from a RECYCLER NEAR YOU, just enter the YEAR of your vehicle and your ZIP code in the above form and press the ’FIND’ button.(What you see below is a previous search for a Toyota Supra Rear Brakes and does not include all the Rear Brakes in YOUR area.). Remove the parking brake cable (B) after removing the fixing clip (A). Loosen the parking brake cable bracket bolts and remove the rear parking brake cable. Parking brake lever travel at 20 kg (44.1 lb, 196 N): 5-8 clicks. If incorrect, adjust the parking brake. IF NECESSARY, ADJUST PARKING BRAKE. NOTE: Before adjusting the parking brake, make sure that the rear brake shoe clearance has been adjusted. For shoe clearance adjustment, see step 10 on page BR-3& (a) Remove the rear console box. For those drag racers who want to run 15 inch or 16 inch rear drag wheels on your MKIV TT! In order to do this you’ve found out by now that your rear drag wheels do not clear your factory TT brakes. The solution is to switch to NA (non-turbo) rear brakes, which consists of calipers, rotors, pads and install kit. You can search the net for a used set of NA rear brakes and have to rebuild them. Double check to make sure nothing is in the way. All pieces should be hanging free (driveshaft, parking brake cable, brake lines, fuel pump & lines) Remove the nuts that retain the rear crossmember and the differential carrier crossmember (4 total) Remove the brake proportioning valve.
NOTE: If any work is done on the brake system or if air is suspected in the brake lines, bleed the system of air.
CAUTION: Do not let brake fluid remain on a painted surface. Wash it off immediately.
1. FILL BRAKE RESERVOIRS WITH BRAKE FLUID
Check the reservoir after bleeding each wheel. Add fluid, if necessary.
2. BLEED MASTER CYLINDER
NOTE: If the master cylinder was disassembled or if the reservoir tank becomes empty, bleed the air from the master cylinder.
(a) Disconnect the brake tubes from the master cylinder.
(b) Depress the brake pedal and hold It.
(c) Block off the outlet plug with your finger, and release the brake pedal.
BEGIN BLEEDING AIR FROM BRAKE CYLINDER WITH LONGEST HYDRAULIC LINE
CONNECT VINYL TUBE TO BRAKE CYLINDER BLEEDER PLUG
Insert other end of the tube in a half-full container of brake fluid.
(a) Slowly pump the brake pedal several times.
(b) While having an assistant press on the pedal, loosen the bleeder plug until fluid starts to runout Then close the bleeder plug.Supra Rear Wheel Drive
(c) Repeat this procedure until there are no more air bubbles in the fluid.
Bleeder plug tightening torque:
REPEAT PROCEDURE FOR EACH WHEEL
CHECK AND ADJUSTMENT OF PARKING BRAKE
1. CHECK THAT PARKING BRAKE LEVER TRAVEL IS CORRECT
Pull the parking brake fever all the way up, and count the notches of lever travel.
How to extract rpf files. Parking brake lever travel at 20 kg (44.1 lb, 196 N):
5-8 clicks
If incorrect, adjust the parking brake.
2. IF NECESSARY, ADJUST PARKING BRAKE
NOTE: Before adjusting the parking brake, make sure that the rear brake shoe clearance has been adjusted.
For shoe clearance adjustment, see step 10 on page BR-3&
(a) Remove the rear console box.
(b) Loosen the lock nut and turn the adjusting screw until the travel is correct.Toyota Supra Rear Differential
(c) Tighten the lock nut and install the console box.Supra Rear End
Was this article helpful?
Download here: http://gg.gg/wxcb7
https://diarynote-jp.indered.space
*Supra Rear Wheel Drive
*Toyota Supra Rear Differential
*Supra Rear End
To find your Toyota Supra Rear Brakes from a RECYCLER NEAR YOU, just enter the YEAR of your vehicle and your ZIP code in the above form and press the ’FIND’ button.(What you see below is a previous search for a Toyota Supra Rear Brakes and does not include all the Rear Brakes in YOUR area.). Remove the parking brake cable (B) after removing the fixing clip (A). Loosen the parking brake cable bracket bolts and remove the rear parking brake cable. Parking brake lever travel at 20 kg (44.1 lb, 196 N): 5-8 clicks. If incorrect, adjust the parking brake. IF NECESSARY, ADJUST PARKING BRAKE. NOTE: Before adjusting the parking brake, make sure that the rear brake shoe clearance has been adjusted. For shoe clearance adjustment, see step 10 on page BR-3& (a) Remove the rear console box. For those drag racers who want to run 15 inch or 16 inch rear drag wheels on your MKIV TT! In order to do this you’ve found out by now that your rear drag wheels do not clear your factory TT brakes. The solution is to switch to NA (non-turbo) rear brakes, which consists of calipers, rotors, pads and install kit. You can search the net for a used set of NA rear brakes and have to rebuild them. Double check to make sure nothing is in the way. All pieces should be hanging free (driveshaft, parking brake cable, brake lines, fuel pump & lines) Remove the nuts that retain the rear crossmember and the differential carrier crossmember (4 total) Remove the brake proportioning valve.
NOTE: If any work is done on the brake system or if air is suspected in the brake lines, bleed the system of air.
CAUTION: Do not let brake fluid remain on a painted surface. Wash it off immediately.
1. FILL BRAKE RESERVOIRS WITH BRAKE FLUID
Check the reservoir after bleeding each wheel. Add fluid, if necessary.
2. BLEED MASTER CYLINDER
NOTE: If the master cylinder was disassembled or if the reservoir tank becomes empty, bleed the air from the master cylinder.
(a) Disconnect the brake tubes from the master cylinder.
(b) Depress the brake pedal and hold It.
(c) Block off the outlet plug with your finger, and release the brake pedal.
BEGIN BLEEDING AIR FROM BRAKE CYLINDER WITH LONGEST HYDRAULIC LINE
CONNECT VINYL TUBE TO BRAKE CYLINDER BLEEDER PLUG
Insert other end of the tube in a half-full container of brake fluid.
(a) Slowly pump the brake pedal several times.
(b) While having an assistant press on the pedal, loosen the bleeder plug until fluid starts to runout Then close the bleeder plug.Supra Rear Wheel Drive
(c) Repeat this procedure until there are no more air bubbles in the fluid.
Bleeder plug tightening torque:
REPEAT PROCEDURE FOR EACH WHEEL
CHECK AND ADJUSTMENT OF PARKING BRAKE
1. CHECK THAT PARKING BRAKE LEVER TRAVEL IS CORRECT
Pull the parking brake fever all the way up, and count the notches of lever travel.
How to extract rpf files. Parking brake lever travel at 20 kg (44.1 lb, 196 N):
5-8 clicks
If incorrect, adjust the parking brake.
2. IF NECESSARY, ADJUST PARKING BRAKE
NOTE: Before adjusting the parking brake, make sure that the rear brake shoe clearance has been adjusted.
For shoe clearance adjustment, see step 10 on page BR-3&
(a) Remove the rear console box.
(b) Loosen the lock nut and turn the adjusting screw until the travel is correct.Toyota Supra Rear Differential
(c) Tighten the lock nut and install the console box.Supra Rear End
Was this article helpful?
Download here: http://gg.gg/wxcb7
https://diarynote-jp.indered.space
コメント